Cílem této práce je vytvořit hardwarovou a softwarovou implementaci testeru modulu měření vibrací turbovrtulových motorů. První část diplomové práce popisuje problematiku měření a monitorování vibrací leteckých motorů v širším kontextu, včetně historie vývoje leteckých motorů. V práci je pak představena specifická aplikace - modul pro monitorování vibrací turbovrtulového motoru včetně popisu konstrukce daného motoru. Na závěr teoretické části je navržena architektura testeru modulu měření vibrací na základě vstupních požadavků. V praktické části práce je popsána implementace funkčního základu testeru modulu měření vibrací jako generátoru dvou nezávislých zdrojů vibrací. Dále je navržena architektura testeru, která byla posléze realizována jako deska plošných spojů vestavěná do 3D tištěné krabičky. Práce dále popisuje implementaci firmware testeru a také softwarový nástroj pro jeho ovládání. Závěrem je porovnán výstup modulu měření vibrací při generovaní vstupních signálů z testeru oproti generátoru signálů.
Anotace v angličtině
The aim of this project was to create hardware and software implementation of a tester for vibration monitoring module for an aircraft turboprop engine. The first part of the thesis describes principles of vibrations monitoring in broader context, including the history of aircraft engines. The vibration monitoring module used in this diploma project is also described here. At the end of the theoretical part, the design of my tester for the vibration monitoring module is discussed, based on the requirements for the module. The second part of thesis describes implementation of two channels vibration signals generator as the basic component of the tester. Then, the tester architecture and its implementation as a printed circuit board along with a 3D-printed box is described. The implementation of the tester firmware, as well as desktop software tool for tester configuration and control is documented as well. Finally, the output of the vibration measurement module when generating input signals from the tester was compared against a signal generator.
Klíčová slova
Vibrace, Letecký motor, Modul měření vibrací, Tester
Cílem této práce je vytvořit hardwarovou a softwarovou implementaci testeru modulu měření vibrací turbovrtulových motorů. První část diplomové práce popisuje problematiku měření a monitorování vibrací leteckých motorů v širším kontextu, včetně historie vývoje leteckých motorů. V práci je pak představena specifická aplikace - modul pro monitorování vibrací turbovrtulového motoru včetně popisu konstrukce daného motoru. Na závěr teoretické části je navržena architektura testeru modulu měření vibrací na základě vstupních požadavků. V praktické části práce je popsána implementace funkčního základu testeru modulu měření vibrací jako generátoru dvou nezávislých zdrojů vibrací. Dále je navržena architektura testeru, která byla posléze realizována jako deska plošných spojů vestavěná do 3D tištěné krabičky. Práce dále popisuje implementaci firmware testeru a také softwarový nástroj pro jeho ovládání. Závěrem je porovnán výstup modulu měření vibrací při generovaní vstupních signálů z testeru oproti generátoru signálů.
Anotace v angličtině
The aim of this project was to create hardware and software implementation of a tester for vibration monitoring module for an aircraft turboprop engine. The first part of the thesis describes principles of vibrations monitoring in broader context, including the history of aircraft engines. The vibration monitoring module used in this diploma project is also described here. At the end of the theoretical part, the design of my tester for the vibration monitoring module is discussed, based on the requirements for the module. The second part of thesis describes implementation of two channels vibration signals generator as the basic component of the tester. Then, the tester architecture and its implementation as a printed circuit board along with a 3D-printed box is described. The implementation of the tester firmware, as well as desktop software tool for tester configuration and control is documented as well. Finally, the output of the vibration measurement module when generating input signals from the tester was compared against a signal generator.
Klíčová slova
Vibrace, Letecký motor, Modul měření vibrací, Tester
Prostudujte vlastnosti a principy funkce modulu pro měření vibrací leteckých motorů.
Vypracujte požadavky pro návrh testeru tohoto modulu.
Na základě požadavků navrhněte architekturu testeru pro modul měření vibrací.
Navrhněte a realizujte plošný spoj elektroniky testeru.
Implementujte firmware testeru a SW nástroj pro jeho ovládání přes PC.
Zásady pro vypracování
Prostudujte vlastnosti a principy funkce modulu pro měření vibrací leteckých motorů.
Vypracujte požadavky pro návrh testeru tohoto modulu.
Na základě požadavků navrhněte architekturu testeru pro modul měření vibrací.
Navrhněte a realizujte plošný spoj elektroniky testeru.
Implementujte firmware testeru a SW nástroj pro jeho ovládání přes PC.
Seznam doporučené literatury
PINKER, Jiří. Mikroprocesory a mikropočítače. 1. vyd. Praha: BEN - technická literatura, 2004, 159 s. ISBN 80-7300-110-1.
VÁŇA, Vladimír. ARM pro začátečníky. 1. vyd. Praha: BEN - technická literatura, 2009, 195 s. ISBN 978-80-7300-246-6.
BODEN, Fritz. Advanced in-flight measurement techniques. New York: Springer, 2013, 344 s. ISBN 978-3-642-34738-2.
BUZDUGAN, Gheorghe. Vibration measurement.Netherlands: Springer, 2010, 345 s. ISBN 978-90-481-8287-9.
BARR, Michael a Anthony J. MASSA. Programming embedded systems: with C and GNU development tools. 2nd ed. Sebastopol: O'Reilly, 2006. ISBN 978-0-596-00983-0.
Seznam doporučené literatury
PINKER, Jiří. Mikroprocesory a mikropočítače. 1. vyd. Praha: BEN - technická literatura, 2004, 159 s. ISBN 80-7300-110-1.
VÁŇA, Vladimír. ARM pro začátečníky. 1. vyd. Praha: BEN - technická literatura, 2009, 195 s. ISBN 978-80-7300-246-6.
BODEN, Fritz. Advanced in-flight measurement techniques. New York: Springer, 2013, 344 s. ISBN 978-3-642-34738-2.
BUZDUGAN, Gheorghe. Vibration measurement.Netherlands: Springer, 2010, 345 s. ISBN 978-90-481-8287-9.
BARR, Michael a Anthony J. MASSA. Programming embedded systems: with C and GNU development tools. 2nd ed. Sebastopol: O'Reilly, 2006. ISBN 978-0-596-00983-0.
Přílohy volně vložené
CD ROM
Přílohy vázané v práci
-
Převzato z knihovny
Ne
Plný text práce
Přílohy
Posudek(y) oponenta
Hodnocení vedoucího
Záznam průběhu obhajoby
Student odprezentoval svou prezentaci, vedoucí přečetl posudky a student odpověděl na všechny dotazy vedoucího/oponenta.
Komise měla následující dotazy:
doc. Kubalčík - Implementoval jste do modulu i samotné měření vibrací ?
doc. Šenkeřík - Bylo by možné řešení vylepšit na měření vibrací pomocí kamer (stereo-kamer) ?