Bakalářská práce popisuje měření tvrdosti (nanotvrdosti) tvarových částí vstřikovacích forem. Byly vybrány čtyři typy povlaků, které byly naneseny na materiál 1.2343 a vzájemně porovnány. Měření tvrdosti bylo realizováno instrumentovanou zkouškou tvrdosti (nanotvrdosti). Instrumentovaná zkouška tvrdosti (nanotvrdosti) byla provedena na nanotvrdoměru (NHT2) Opx/Cpx od firmy CSM Instruments při aplikovaném zatížení 10mN. Z výsledků měření vyplynul výrazný nárůst tvrdosti u nanesených povlaků v porovnání se základním materiálem.
Annotation in English
This thesis describes the measurement of hardness (nanohardness) molded parts injection molds. They were selected four types of coatings that were applied to the material 1.2343 and mutually compared. Hardness measurements were carried instrumented hardness test (nanohardness). Instrumented hardness test (nanohardness) was performed on the machine (NHT2) OPX / CPX from CSM Instruments at an applied load 10mn. The results of the measurements resulted significant increase in hardness with applied coatings in comparison with the base material.
Keywords
tvrdost, měření tvrdosti, funkční části formy, Instrumentovaná zkouška tvrdosti DSI
Keywords in English
hardness, measuring of hardness, functional parts of mold, instrumented test of hardness
Length of the covering note
65 s.
Language
CZ
Annotation
Bakalářská práce popisuje měření tvrdosti (nanotvrdosti) tvarových částí vstřikovacích forem. Byly vybrány čtyři typy povlaků, které byly naneseny na materiál 1.2343 a vzájemně porovnány. Měření tvrdosti bylo realizováno instrumentovanou zkouškou tvrdosti (nanotvrdosti). Instrumentovaná zkouška tvrdosti (nanotvrdosti) byla provedena na nanotvrdoměru (NHT2) Opx/Cpx od firmy CSM Instruments při aplikovaném zatížení 10mN. Z výsledků měření vyplynul výrazný nárůst tvrdosti u nanesených povlaků v porovnání se základním materiálem.
Annotation in English
This thesis describes the measurement of hardness (nanohardness) molded parts injection molds. They were selected four types of coatings that were applied to the material 1.2343 and mutually compared. Hardness measurements were carried instrumented hardness test (nanohardness). Instrumented hardness test (nanohardness) was performed on the machine (NHT2) OPX / CPX from CSM Instruments at an applied load 10mn. The results of the measurements resulted significant increase in hardness with applied coatings in comparison with the base material.
Keywords
tvrdost, měření tvrdosti, funkční části formy, Instrumentovaná zkouška tvrdosti DSI
Keywords in English
hardness, measuring of hardness, functional parts of mold, instrumented test of hardness
Research Plan
\begin {arab}
Vypracování literární studie na dané téma
Příprava zkušebních těles pro experimentální část
Provedení experimentu
Vyhodnocení naměřených výsledků
\end {arab}
Research Plan
\begin {arab}
Vypracování literární studie na dané téma
Příprava zkušebních těles pro experimentální část
Provedení experimentu
Vyhodnocení naměřených výsledků
\end {arab}
Recommended resources
Dle doporučení vedoucího BP
Recommended resources
Dle doporučení vedoucího BP
Enclosed appendices
1 CD ROM
Appendices bound in thesis
graphs, tables
Taken from the library
No
Full text of the thesis
Appendices
Reviewer's report
Supervisor's report
Defence procedure record
- Čím si vysvětlujete rozdíly naměřených výsledků? - doc. Ing. Martina Hřibová, Ph.D.
- Jaké statistické vyhodnocení jste provedl? - Ing. Dana Shejbalová, Ph.D.
- Jaký je minimální počet měření aby byli výsledky vypovídající? - Ing. Dana Shejbalová, Ph.D.
- Řešil jste měření tvrdosti nebo jste pouze měřil? - Ing. František Volek, CSc.